Count me in I'll have a couple if you order them.
Alan Burrows
-----Original Message-----
From: owner-europa-list-server@matronics.com
[mailto:owner-europa-list-server@matronics.com] On Behalf Of rlborger
Subject: Europa-List: Fwd: Aircraft Spruce Quote for the BIG pip pins
Fellow Europaphiles,
I received the attached quote from Aircraft Spruce. The $41.10 each
for 25 minimum order.
Begin forwarded message:
> From: amystinchcomb@aircraftspruce.com (Amy Stinchcomb)
> Date: September 21, 2004 12:30:03 PM CDT
> To: rlborger@mac.com
> Subject: Aircraft Spruce Quote
>
>
> AIRCRAFT SPRUCE AND SPECIALTY
> 225 AIRPORT CIRCLE - PO BOX 4000
> CORONA, CA 92880
> 951-372-9555 *** 951-372-0555 FAX
>
>
> Thank you for your recent inquiry for quotes. Please be advised that
> these
> prices are quotes only, and are subject to change. Shipping charges
> and
> any applicable state taxes will be added at time of shipping. Please
> refer
> to quote# 216009 when placing the order. This quote is good for 30
> days.
>
> SPECIAL ORDER QUICK RELEASE PIN
> SIZE 1/2" DIAMETER, 3-3/4 GRIP
> PART #QRP2C083.75 QTY. 25
> $41.10 EACH 8 WEEKS LEAD TIEM
> THANK YOU FOR YOUR ORDER
>
> Total Quote: $N/A
>
> We accept MasterCard and Visa or a bank transfer to:
> Union Bank of California/Sunny Hills
> 1080 E. Bastanchury Rd.
> Fullerton, CA 92835
> Acct# 0650022394 / ABA (Route) 122000496
> International Swift Code: BOFCUS33MPK
> Payable to: Irwin International dba Aircraft Spruce
> Please add $20 for bank transfer fees
>
> Thank you.
> Sincerely,
> Amy Stinchcomb
>
>
> ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
> AIRCRAFT SPRUCE & SPECIALTY CO
> 225 Airport Circle
> Corona, CA 92878 USA
> Tel: 951-372-9555
> Fax: 951-372-0555
> Toll Free: 877-4SPRUCE (477-7823)
> Email: amystinchcomb@aircraftspruce.com
> WWW: http://www.aircraftspruce.com
> ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
>
McMaster-Carr has two pins which seem suitable.
The basic, T-Handle pin is $29.30 each
The heavy-duty, T-Handle pin is $57.08 each.
I received one each of these pins from McMaster-Carr today. I will
post pics and a description of the McMaster-Carr pins on the Europa
Forum site this evening.
I also received the smaller 1/4" pins I ordered from McMaster-Carr. I
think they are unsuitable for flight use, but could be used during
alignment assembly and ground assembly. But I'd attach a big red
ribbon to them to ensure that no flight was made with them in place
instead of the proper pins.
Three e-mails to Europa (2004). No replies yet.
Good building and great flying,
Bob Borger
Europa Kit #A221 N914XL, XS Mono, 914, Airmaster C/S
http://forum.okhuijsen.org/N914XL
(75%) tail kit done, wings closed, cockpit module installed, pitch
system in, landing gear frame in, rudder system in, outrigger mod in,
Fuselage Top on, lift/drag/flap pins in, wing incidence set, tie bar
in, flap drive in. Working in - 24 Instrument Panel, 25 Electrical, 27
Setting Wings, 28 Flaps, 29 Main Gear, 30 Fuel System, 32 Tail, 34 Door
Latches & 35 Doors, 37 Finishing.
3705 Lynchburg Dr.
Corinth, TX 76208
Home: 940-497-2123
Cel: 817-992-1117
==
direct advertising on the Matronics Forums.
==
==
==
|