Hi Stevie
Now I have some questions.
The wheel ramp attachment bar, where did it come from? Was it with
the trailer or did you make it.
They are self made. There is one extra advantage with them:
the ramp has quite a tight fit to the monogear and they are difficult
to separate. By using these attachment bars /giant turnbuckles
you can force the ramp move upp AND also down (by chain only upp).
Look at the attachment.
Did the mud guards come with the trailer or did you add them. As you
can see I don't any.
The mud guards come with the trailer with one axle. The other safety
axle
and it=B4s mud guards have added here later.
Because of my accidents "tail wheel drops down when pushing the plane
to the trailer" I will instal this week a floor to the trailer. I
think it prevents
some future damages and also it will prevent shit coming when towing.
Probably one day I have also walls and roof and the trailer is
modified to be
a lorry...
Extra main wheel ramp is also an essential equipment - I will have it
also soon.
I wanna point out I really respect those people who are able to rigg
Europa alone. When only moving wings alone my heart has a rate of
200...
Regards, Raimo
===========
Raimo M W Toivio
OH-XRT Europa XS Mono #417, test flying
OH-CVK C172 Skyhawk, engine overhauling
OH-BLL Beechcraft C45, w radial engines (grounded)
37500 Lempaala
Finland
tel + 358 3 3753 777
fax + 358 3 3753 100
gsm + 358 40 590 1450
raimo.toivio@rwm.fi
www.rwm.fi
____________________________________________________________
Steve Crimm - BIT, CDIA+, OCSA, OCWA
Stephen Scott & Associates, Inc.
Your Exclusive Source for Automated Data Capture Solutions
Email: steve.crimm@stephenscott.com
Web Site: www.stephenscott.com
Phone: 678-461-7957 Fax 678-461-7958
"The agony of poor service lasts much longer than the thrill of low
price"
____________________________________________________________
Confidentiality Note: The information contained in this message may be
privileged and
confidential. If you are not the intended recipient of this
information, you are hereby
notified that any dissemination, distribution or copying of this
communication is strictly
prohibited. If you have received this communication in error, please
reply to the sender
immediately and delete the message from your computer. Thank You
-------------------------------------------------------------------------
-----
From: owner-europa-list-server@matronics.com
[mailto:owner-europa-list-server@matronics.com] On Behalf Of Raimo
Toivio
Sent: Tuesday, May 22, 2007 18:15
To: europa-list@matronics.com
Subject: Re: Europa-List: trailer wing support profile.
Hi Keith
I did not like those original rubber straps
and removed them. I made new supporters
just like you described them. They are 2" /50 mm
thick wooden blocks (birch plywood board)
and I shaped them by CNC cutter.
They match well to the wing section
and between there are very soft self
adhesive stuf, douple layers.
If you like to get the drawing, please
contact me direct.
Because the pip pins let the supporters
to move a bit, I secure supporters to the
trailer also by extra 13 mm / =BD" bolt & nut.
There are still some movements between
wings and trailer supporters - to prevent any
damages in my first class wing surfaces
I cover the wings by kitchen film before
dropping them to the trailer.
The spars are secured by clamps tightened
by bolts - not only by pip - pins like original
factory trailer. I do not wanna get any damages
to the spars=B4main pip pin holes.
I have also some other modifications like
douple axle for security reasons. Look at the pics.
The riskiest part to operate Europa in my case
has been so far when pushing it to the trailer:
- I have almost destroyed my rudder by hitting it
to the back door of my van=B4s (it was open)
- main wheel gate opened when towing the trailer
(I was lucky Europa did not dropped to the road
because it was fixed by bolts in the tail wheel
and it was not on it=B4s side because I have extra
side supporters). To prevent this situation meet
me again I connected those turnbuckles keeping
gate up together by a strong rubber string with
hooks which prevent them to open spontaneously.
- tail wheel dropped from the rail and transponder
/DME antenna went broken
- tail wheel dropped yesterday again from the rail
and Dynon=B4s OAT sensor went broken and penetrated
through Europas stomach (so I have a similar extra hole
in my Europa=B4s fuselage as Ferg Kyle has his wing=B4s
leading edge!)
Personally I think the only almost safe way to carry
Europa on the roads is to carry it in a big enough lorry
/truck with closed coach. No towing at all. Only flying...
Raimo
====
Raimo M W Toivio
OH-XRT Europa XS Mono #417, 3h42min and 12 landings in the log book
OH-CVK C172 Skyhawk, reinterioring completed, engine will be
overhauled also for surprise
OH-BLL Beechcraft C45, w radial engines (grounded for ever)
37500 Lempaala
Finland
tel + 358 3 3753 777
fax + 358 3 3753 100
gsm + 358 40 590 1450
raimo.toivio@rwm.fi
www.rwm.fi
----- Original Message -----
From: Keith Hickling
To: Eurpoa List
Sent: Tuesday, May 22, 2007 8:41 AM
Subject: Europa-List: trailer wing support profile.
Does anyone have a wing profile forward of the spar at the position
of the wing support on the factory trailer? On my drawing this is 2
metres from the root spar pin bush. If anyone has one they could email
or post to me I would be very grateful and it would save a lot of work
trying to transcribe it from the wing. I need it to get the trailer wing
supports made.
Keith Hickling,
New Zealand.
href="http://www.matronics.com/Navigator?Europa-List";>http://www.matron
href="http://forums.matronics.com";>http://forums.matronics.com
|