I am converting my monowheel to a taildragger (down at Flight Crafters
in Lakeland Fla)so I can sell my out riggers and my monowheel parts if
you (or anyone) is interested.
Richard Sementilli
>
> Hi again folks.
> I got the outrigger wheels and also a sealed tail wheel from: Linco.
> www.linco-inc.com email: linco@flash.net
> Sorry, I can't find the invoice with the product # but you can figure out
> what you want. My tail wheel is a #5.00006.565 6"x2" ball bearing (sealed)
> round tread.
> I have the original supplied outrigger and tail wheels (XS) for a Santa
> special price of FREE!
> Merry Humbug!
> Tom XS Jab Airmaster N96V Atascadero, CA
>
> -----Original Message-----
> From: owner-europa-list-server@matronics.com
> [mailto:owner-europa-list-server@matronics.com] On Behalf Of
> beecho@beecho.org
> To: europa-list@matronics.com
> Subject: RE: Europa-List: Outrigger wheels
>
>
> I have a source for the softer, quieter sealed bearing wheels as advocated
> by Dennis Voorhees. I have to look in my records and will do so and post.
> They can be ordered on line. Tom Friedland
>
> -----Original Message-----
> From: owner-europa-list-server@matronics.com
> [mailto:owner-europa-list-server@matronics.com] On Behalf Of Ronald J.
> Parigoris
> To: europa-list@matronics.com
> Subject: Re: Europa-List: Outrigger wheels
>
> --> <rparigor@suffolk.lib.ny.us>
>
> Hello Jim
>
> "Does anyone know of a source for the outrigger wheels"
>
> I am not flying yet. Here is a post I made 01-2004
>
> I finally got around to installing Colson 4" x 4.25" Gray Flat profile
> Hi-Tech Performa. They have ball Bearings and a 3/8 hole. They are not
> sealed ball bearings.
>
> I forget who I told I would report to when I figured out how to make a
> spacer/dirt shield for the bearings.
>
> I used 18-8 SS 3/8-24 2.5 length Hex cap screws. McMaster PN 92198A361
>
> www.mcmaster.com
>
> and 18-8 thin Nylon Insert Locknuts McMaster PN 90101A245
>
> I needed to drill outrigger forks to 3/8 hole.
>
> I made the spacers out of 1.25 inch aluminium bar.
>
> Dimensions of spacer:
>
> 1.010" OD
>
> 3/8 hole through center.
>
> Pocket .165" deep and .935 ID
>
> I actual made the Pocket depth ~.175, and fit exact to wheels by sneaking
> off a few thousands at a time.
>
> The seal is going to keep out dirt pretty good.
>
> Overall completed weight is probably very similar to the stock, perhaps a
> bit lighter.
>
> I purchased from:
>
> Thank you for the inquiry
> Rich
> Pooley Inc
> 800-428-2606
> 716-852-3780
> 716-852-3788 fax
>
> Ron Parigoris
>
> I am thinking on Glider Wings to use In Line skate wheels:
>
> Anyone ever try Inline skate wheels as a replacement for outrigger wheels?
>
> Check out 100MM ones here:
>
> http://www.nettracing.com/wheels.htm
>
> I am sure you can get sealed BBs for them.
>
> Ron Parigoris
>
> advertising on the Matronics Forums.
>
> --
> Checked by AVG Anti-Virus.
>
> --
> Checked by AVG Anti-Virus.
>
> advertising on the Matronics Forums.
>
> --
> Checked by AVG Anti-Virus.
>
> --
> Checked by AVG Anti-Virus.
>
>
>
|