Cool - it should work then. Saves anyone with an XP or Windows 2000 laptop
having to install native DOS!
Cheers,
Jeremy
Jeremy Davey
Europa Monowheel 537M G-EZZA
Tail done
Standard XS wings with mods underway
CM installed in fuse (with airbrakes fittings)
1200 build hours to date
Intended fit:
Rotax 914 turbo, Airmaster CS fully-feathering prop
Lots of lights, buttons, switches, gizmos, and alarms
-----Original Message-----
From: owner-europa-list-server@matronics.com
[mailto:owner-europa-list-server@matronics.com] On Behalf Of Paul Boulet
Subject: RE: Europa-List: Throttle setting software
It's been a couple months so my memory a bit foggy but
I do believe it was COM1. I'm not familiar with
Virtual PC... I run Windows NT on my laptop and know
that dos prompt would not work
Paul
--- Jeremy Davey <EuropaFlyer_3@msn.com> wrote:
> <EuropaFlyer_3@msn.com>
>
> Which port does it use, Paul - the serial COM1? I
> can try this under
> VirtualPC as that might save a few people a
> headache!
>
> Cheers,
> Jeremy
>
> Jeremy Davey
> Europa Monowheel 537M G-EZZA
> Tail done
> Standard XS wings with mods underway
> CM installed in fuse (with airbrakes fittings)
> 1200 build hours to date
> Intended fit:
> Rotax 914 turbo, Airmaster CS fully-feathering prop
> Lots of lights, buttons, switches, gizmos, and
> alarms
>
> -----Original Message-----
> From: owner-europa-list-server@matronics.com
> [mailto:owner-europa-list-server@matronics.com] On
> Behalf Of Paul Boulet
> To: europa-list@matronics.com
> Subject: RE: Europa-List: Throttle setting software
>
> <possibletodo@yahoo.com>
>
> It should also be noted that you must boot your
> computer up with DOS (not the dos prompt that comes
> with windows) in order for this to run
> correctly...took me lots of trial/error before I
> figured this out!
> Paul Boulet, N914PB
> Awaiting test pilot before i can fly
> --- G-IANI <g-iani@ntlworld.com> wrote:
>
> > <g-iani@ntlworld.com>
> >
> > "Does anyone out there have the throttle setting
> > software for the 914 they
> > can e-mail me? Also any tips or issues on its
> > use?"
> >
> >
> > You will find the 914 software on the Europa
> Factory
> > site
> > (http://www.europa-aircraft.com/) under Builders
> > support. The file is quite
> > small and downloads OK. This is the most recent
> > version and works OK. If
> > you have any questions let me know.
> >
> > Ian Rickard #505 G-IANI XS Trigear
> > Europa Club Assistant Mods Rep
> > e-mail mods@europaclub.org.uk
> >
> >
> >
> > Contributions
> > any other
> > Forums.
> >
> > http://www.matronics.com/chat
> >
> > http://www.matronics.com/subscription
> > http://www.matronics.com/FAQ/Europa-List.htm
> > http://www.matronics.com/archives
> > http://www.matronics.com/photoshare
> > http://www.matronics.com/emaillists
> >
> >
> >
> >
> >
> >
>
>
>
> Contributions
> any other
> Forums.
>
> http://www.matronics.com/chat
>
> http://www.matronics.com/subscription
> http://www.matronics.com/FAQ/Europa-List.htm
> http://www.matronics.com/archives
> http://www.matronics.com/photoshare
> http://www.matronics.com/emaillists
>
>
>
>
>
>
|