I would only be close to Leicester if you bought me a ticket from
brisbane australia to heathrow : )
So how did you go ???
-----Original Message-----
From: owner-europa-list-server@matronics.com
[mailto:owner-europa-list-server@matronics.com]On Behalf Of Herve
Sent: Thursday, 3 July 2008 5:59 PM
Subject: Fwd: RE: Europa-List: mod 59
Hi Craig
Thank you very much for your advise.Will have a go this week end.You
wouldn't be close to leicester?
Regards
Herve
From: Herve <hervechaussures@tiscali.co.uk>
>Subject: Fwd: RE: Europa-List: mod 59
>
>
>>From: "craig bastin" <craigb@onthenet.com.au>
>>To: <europa-list@matronics.com>
>>Subject: RE: Europa-List: mod 59
>>Date: Wed, 2 Jul 2008 22:09:56 +1000
>>Sender: owner-europa-list-server@matronics.com
>>Reply-To: europa-list@matronics.com
>>X-Antivirus: AVG for E-mail 7.5.524 [270.4.3/1529]
>>
>>
>>Yes i have done it. It is quite simple
>>undo the nut from the top of the shaft that holds the nose wheel fork
>>remove the fork and all the washers, spacers etc, THE PIN, and in the kit
>>you will find the small steel ring about 1.5mm thick that will slide
>>onto the shaft of the nose wheel fork, slide the whole thing
>>back into gear leg without anything else on there, just the small ring
from
>>the kit
>>then put the big ring from the kit on top of the gear leg and a couple of
>>washers on top of the ring
>>then a half inch nut, there SHOULD be a gap under the washers. tighten up
>>the nut until the
>>flat plates on the top of the nose wheel and the bottom of the gear leg
>>touch. This should have the
>>small steel ring inside the bottom of the gear leg. Then remove the nut
and
>>washers, remove the
>>nose wheel and the two steel rings (which you no longer need), At this
point
>>the inner sleve
>>may be sticking up out the top of the gear leg, if so, cut/file it off
till
>>it's nice and flush.
>>put the whole thing back together but this time put the rubber o-ring on
top
>>of the shimmy plate, so
>>when you slide the nose wheel back into the leg it will be inside the
bottom
>>of the gear leg (where the small steel ring was)
>>then put the washers (new bigger ones from the kit) plus 4 of the old ones
>>on the top with your Castelated Nut (the one with the slots cut in it)
>>on and re-set the tension as per the manual
>>
>>Just so you know, My gear leg already had space for the o-ring in the
>>bottom, so maybe you can just fit the o-ring.
>>
>>hope this helps you, sorry i dont have any pictures, I did it as part of
the
>>build and it took about 30 seconds
>>
>>regards
>>
>>craig
>>
>>-----Original Message-----
>>From: owner-europa-list-server@matronics.com
>>[mailto:owner-europa-list-server@matronics.com]On Behalf Of Herve
>>Sent: Wednesday, 2 July 2008 6:32 PM
>>To: europa-list@matronics.com
>>Subject: Europa-List: mod 59
>>
>>
>>
>>Hello
>>I am trying to do mod 59 (nose wheel shimmy damper) and I am a little
>>confuse as to what is what and goes where.Has anyone got some
>>pictures to explain?
>>G.CHET europa xs turbo
>>Herve
>>
>>
>>
>>
>>
>>Checked by AVG.
>>7:23 PM
>>
>>Checked by AVG.
>>7:23 PM
>>
>>
>>
>>
>>
>>
>>
>>--
>>Checked by AVG.
>>7/1/2008 7:23 PM
Checked by AVG.
10:15 AM
Checked by AVG.
10:15 AM
|