Hi Bud,
Could you please elaborate where the fouling is more specifically? I appreci
ate knowing this, so I am thankful Bob brought it up. I have the top still o
ff so its ideal I overcome these issues now.
Regards
Tony Renshaw
> On 23 May 2014, at 7:40, "Bud Yerly" <budyerly@msn.com> wrote:
>
> Bob,
> You are right on the money. Every aircraft I have built needed about 1/8 o
ff each clevis on the pitch mechanism to allow the trim bar to clear at full
elevator and trim travel. As for interpreting the English Language.... No c
omment.
> Regards,
> Bud Yerly
>
> ----- Original Message -----
> From: Fred Klein
> To: europa-list@matronics.com
> Sent: Thursday, May 22, 2014 10:30 AM
> Subject: Europa-List: Re: Clevice \Forks debacle.........
>
> Bobthank you for your attention to my build photo and for alertin
g me to this issue, however vexing you may find it.
>
> I am simply baffled to learn that you find =9Cthere is already enoug
h shit flying about on the issue=9D and that it=99s an example s
howing that =9Cpeople just can=99t read and interpret the Englis
h language=9Dplease do not attempt to elaborateI can
do without further discussion which you find unsuitable for posting on Matr
onics.
>
> Fred
>
>
>> On May 22, 2014, at 2:19 AM, Bob Harrison <ptag.dev@talktalk.net> wrote:
>>
>> Hi! Tony /Fred.
>> To try to help you over this vexed issue concerning the clevis forks I ju
st spoke to a local friend on the issue ....his immediate response was t
hat he had removed =C2=BC=9D but when I questioned him further he sta
rted to apply some engineering reason to the issue and suggested that we pro
bably both removed 1/8=9D from each clevice to ensure there was adequa
te thread purchase left on both clevices. Which is the principle I would app
ly , the only thing better is to remove it from one and check the operationa
l clearance as to whether it is necessary to do the other too.
>> I=99m not publishing this on the Matronics site since there is alre
ady enough shit flying about on the issue , people just can=99t read a
nd interpret the English language !
>> Regards
>> Bob H
>
>
>
>
>
> href="http://www.matronics.com/Navigator?Europa-List";>http://www.matronh
ref="http://forums.matronics.com";>http://forums.matronics.com
> href="http://www.matronics.com/contribution";>http://www.matronics.com/c
>
>
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
>
|